220V Flame Retardant Test In Fires Heat Release Rate Checking Thermal Conductivity Lab
Product Application
The name Cone Calorimeter is derived from the conical heater as used by Dr. Vytenis Babrauskas to inspect test specimen(100×100) with flux up to 100/ for the bench scale oxygen depletion of his development.
ISO Solution Fire Testing Equipment Cone Calorimeter is based on the theory that pure combustion calories are in proportion to a necessary amount of oxygen for combustion and 13.1 MJ/kg is generated whenever oxygen 1kg is consumed, and heat emission, ignition time, oxygen consumption, CO and CO2 generation, and flow of ignited gases as generated from test materials are measured.
ISO Solution Fire Testing Equipment Cone Calorimeter, as properly sized for lab use, is designed to enable auto operation of all units connected with DAQ(Data Acquisition) Program so that user can conveniently perform test. Also, it reduces installation space and automatically advances test with the 17inch Touch Screen. This tester fully meets the international standard.
Technology data:
1.) 19inch standard instrument frame,17inch touchable screen pc insert
2.) cone heater powering rating:5000w,heat output rate:0~100kw/m2
3.) in the range of 50*50mm in the center surface of expose test sample ,center irradiation error no more than +-2%;
4.) sample size:100mm*100mm*50mm
5.) weight range:0~2000g;precision:0.1g;
6.) ignition system with safe cut device high pressure spark generator ,automatic positioning
7.) clockwise magnetic oxygen analyzer ,adopt pressure change of clockwise magnetic to measure the oxygen density
8.) density range:0-25%,T90<1.5S,zero drift:<0.5%month,measure data deviation<0.5%month,
9.) non-dispersion infrared co and co2 analyzer:co:0~1%;co2:0~10%;
10.) smoke analyzer use laser system test smoke density,and this system was made up of photoelectricity two-electrode valve,0.5mv He-Ne laser,main graphics detector and auxiliary graphics detector .
11.)exhaust system was made up of fan,hottle,air intake and exhaust tube of fan and orifice meter.exhaust gas flow 0~50g/s can be adjusted,precision 0.1g/s.
12.)ring sampler need to be located in the air take tube at distance of 685mm against hottle ,need to be 12 holes existed in the sampler in order to homogeneous air flow component.
13.) exhaust gas flow need to be measured by the differencial pressure of side of hole plate above the fans at the distance of 350mm,the inner diameter of hole plate is 57mm+-1mm;
14.) the temperature of air flow is tested by armored thermocouple with closed node of diameter 1.6mm,thermocouple need to be located in 100 mm above the orifice plate;
15.) gas sampling system including ring sampler ,sampling pump,filter,cold trap,waste water exhaust,water filter and co2 filter;
16.) cold trap:0~5 degree,diaphragm pump,flow rate :261/min,vacuum degree:700mm Hg
Sample size
|
100*100*50mm
|
Weight range
|
0-200g
|
precision
|
0.1g
|
Density range
|
0-25%
|
T90
|
<1.5S
|
Zero drift
|
<0.5%month
|
Measure data deviation
|
<0.5%month
|
Structure of cone calorimeter
1.)The combustion chamber: the conical heater, the 10KV ignition device, the control circuit, the windshield, etc..
2.)Oxygen analyzer: Servomex analyser, oxygen analyzer can accurately test the content of oxygen in the air pipe in the time of the change, and then by the instantaneous oxygen concentration and oxygen consumption principle to determine the heat release of the material.
3.)Load table: a device for measuring the quality of the sample, which can accurately record the mass change of the sample in the process of combustion
4.)Smoke measurement system: He Ne laser emitter and double electron beam measuring device, which can be used to determine the specific extinction area (SEA) of the smoke in the smoke pipe.
5.)Ventilation system: the ventilation system is a sample of the combustion products from the combustion chamber to the atmosphere in the device
6.) Other improvement equipment: according to different needs, can also add other analysis device, such as the analysis of the combustion products, can increase the infrared spectrum analysis device; if the temperature distribution in the sample, the corresponding thermocouple or infrared imaging device.
7.) Auxiliary equipment: auxiliary equipment includes microcomputer processor, heat flow meter device, removing CO2 and H2O (gas), etc..
Product Tags:
|
|
220V Flame Retardant Test In Fires Heat Release Rate Checking Thermal Conductivity Lab Images
|
